FAQ
2 POST LIFTS
All cars and light trucks have approved lifting points that are specified by the vehicle manufacturer. It is critical that your vehicle is positioned properly relative to the centre line of the lift and centred between the columns. Cars that are front wheel drive and can be lifted asymmetrically. This allows the car to be positioned further back from the centre line of the lift. Often, a good rule of thumb is to start with the steering wheel lined up under the centre of the lift. When this is done, check the position of the four arms when they are extended to the recommended lifting points. The front lifting arm is manufactured on an angle and is considerably shorter than the rear arm, which will accommodate the asymmetric loading of your vehicle.
Yes . You just need to purchase the , std equalizer cables , Std length Safety cable, and the short version of the long hose.
No, you cannot install a two post lift on asphalt. Concrete must be a minimum of 4 -6" thick depending on capacity with a minimum rating of 3000 PSI.
Lifts can be installed but need to have the heating elements mapped so the bolts don't damage the heating system. We can help you find a suitable contractor to help in this regard.
Both BendPak and Peak offer a TURF Kit option for their 9-10K Capacity Lifts. The turf kit provides service on large fairway mowers to greens mowers, utility carts, sand groomers, fertilizer sprayers, golf and refreshment carts. Fully adjustable wheel span and fork assemblies fit a wide array of wheel arrangements.
1.Run the lift up and down a few times with no vehicle. 2.Lower arms to about 1 foot off the ground. 3.Slightly open the Allen bleeders on top of the cylinders, look for bubbles in the fluid. Once there are no more bubbles, close the Allen bleeders. This should take care of the issue.
1. Run the lift up and down a few times with no vehicle.
2. Lower arms to about 1 foot off the ground.
3. Slightly open the Allen bleeders on top of the cylinders, look for bubbles in the fluid. Once there are no more bubbles, close the Allen bleeders.
Yes you can, you would purchase an extension kit which would contain longer hydraulic hoses and cables.
We have different options to choose from depending on the weight capacity required, a sales rep would be happy to discuss options that suit your needs.
No. All 2 post lifts require anchoring. Talk to a sales representative about lift options that do not require anchoring.
We recommend frame cradle pads for added safety on all 2 post lifts
Frame cradle pads are recommended with 2 post lifts when working on any pickup truck or full frame vehicle. They act as a saddle for the frame rail and prevent the vehicle from sliding off the lift arms.
Symmetrical lifts have arms at the front and back that are the same length and design. Asymmetrical lifts have arms at the front and back that are different. This allows better access to the interior of the vehicle that is being worked on as well as better balance for different vehicles.
80-100 ft/lbs is sufficient and should be checked at regular service intervals.
Clear Floor models have the cables running over head giving a smooth floor under the lift making it easier to work under the car and roll tool boxes and transmission jacks under the car when working on it. Floor Plate models have the cables running under a cover on the floor giving more height for tall vans and the like. They both work well in different situations. Your sales professional can go over all of the details and find the perfect solution for your needs.
It's located inside the carriage about 18” down from the top of the carriage.
If you've got a heavy vehicle to lift, especially a truck, then you're going to want a set of cradle pads. Sturdy steel construction keeps the frame firmly between the cradle, while the treaded rubber mats protect the finish and reduce the chance of slippage.
Lifts (4 Posts)
Ramps are removable, We offer ramp stops as an add on accessory to flush the ramps with the runway or you can remove them completely.
Yes 220v is an option. The lift comes standard 110 but talk to a sales representative about changing to 220v
No, the vehicle cannot be stored on the car lift while the portable wheel kit is in use. This will damage the wheel kit and void any warranty for damage caused by this sort of incorrect usage.
You can leave the vehicle on the Jack indefinitely, as long as you leave the Rolling Jack engaged on its Safety Locks. Once the Safety Locks are engaged, the mechanical action of the lock holds the Vehicle up, so a loss of air or hydraulic pressure has no impact; your Vehicle is going to stay where you left it. Always leave your Rolling Jack either fully lowered or engaged on its Safety Locks.
6ft
You are welcome to leave your sub 9000 lb lift free standing but it is always recommended to put some sort of barrier between the posts and the concrete such as a yoga matt or recycled tire matting. 3mm rubber gym flooring also works great in this circumstance.
The 4 post lifts are stocked with steel and are available in an extended version as well. We also offer an aluminum option in standard or extended as well at extra cost.
Yes, any post on the lift can be shimmed
10 Gauge or 1/8th" steel with cold formed inner guide supports.
The Air-Operated Hydraulic Pump must be attached to an air supply: 20 cubic feet per minute (.57 cubic meters per minute) and 100 psi (7 bar).
90 seconds on 110V . 45 seconds on 220V power
No, a certified electrician is required to wire 220V power
General Questions
No, Babco is the sole distributor for BendPak products across Canada.
Yes, you can pick up the unit from our warehouse in Surrey BC or Mississauga ON, we have forklifts to load it to your trailer. Do check the weight and dimension before planning a pickup. Also, it’s always better to book a pickup date and time so that we can ensure you timely service.
Yes, we will perform a site survey in our service areas for a fee of $150. One of our seasoned technicians, will visit the site, measure for fitment, assess any issues and give you advise on moving forward. This gives many customers extra peace of mind if they are struggling with measurements or specific site challenges.
Please ensure that any lift installation on a suspended slab, regardless of thickness is approved by an engineer prior to installation. This is the only way to ensure the safety of the installation.
This depends on the product being purchased, and where it is being shipped to. Many pieces of equipment have a freight allowance which for many major cities would allow us to ship at no charge. Outside major cities often carries a large premium on shipping rates, which we are not able to fully absorb. Please contact a sales representative to verify shipping costs.
We do offer a lease option on our lifts to facilitate your purchase. Your salesperson would be happy to go over the details with you once you have selected an appropriate model
We offer financing on a lease to own program with Catalyst Financial. Please ask your sales rep for more details.
Yes. We do have a maximum amount of $10,000 on a credit card. Please contact a sales representative about different payment options.
As we are a wholesaler and purchase on volume, we keep our prices as low as possible for our customers and are usually the best price in town.
Due to current DOT and insurance laws regarding the transport of hydraulic oils (DOT Section 1 - Hazardous Ingredients; DOT Section 2 - Fire and Explosion Hazards and DOT Section 3 - Health Hazards) the required hydraulic fluid is to be supplied by the end-user, only. BendPak lifts are designed to operate using standard 10-weight, non-foaming, non-detergent hydraulic oil or Dexron-III ATF fluid. This is available in virtually any automotive store.
No. They come with a 5 inch pigtail. You will need your electrician to either add a plug to it or hard wire it in to your electrical service.
You can call the 1-800 number or send an email to support@babco.ca. Leave specific information and the correct person will get back to you as soon as they can. Keep in mind that we are closed on weekends and Holidays so Mondays or the first day back after a long weekend can be a busy day.
To determine the slab thickness, drill a small hole in the slab and measure the depth after the drill goes through the slab. You will feel the resistance change when you have gone through the slab. You can also mark 4.5-5" on the drill bit with a piece of tape if the slab is thicker to ensure proper depth.
Leave about 6” of space between from the edges of your lift's baseplate to the edges of any concrete slab.
This is dependent on the type of lift and where it is being installed. It will take anywhere from 4 to 6 hours on average for a single 2 post or 4 post install. Other variations or unique locations could add time to the install.
We keep an average of $6,000,000 in inventory in our warehouses across Canada. While we strive to have anything that you are looking for immediately on hand, occasionally due to demand or shipping issues, it could take up to 4-5 months to receive your product. It is best to order as soon as you can if immediate delivery is of concern.
Measurements and dimensions are provided on our website and it is usually pretty simple to figure out if a lift will fit. If you have questions, one of our installers can do a site visit to make certain that your chosen lift will fit. There is a fee of $150 for this service.
Once the install check list is received, an install date will be mutually agreed upon at which point you will receive a confirmation stating the date and time along with any further information that may need to be conveyed.
We would need the make , model , year and possibly the serial number plus a brief description of what you need or pictures of the issue. Also if you could let us know what is the machine doing or not doing, that would help us get started on fixing your issue.
Until the lift is in our warehouse we can not book the install as there are too many variables to set an an accurate delivery date. Once it has arrived, we will let you know and book a convenient time for your install.
Yes we sell it and would be happy to install it. There would of course be a service fee for us to install it for you.
Please call our 1-800 number or send an email to support@babco.ca. We will first see if we can troubleshoot it over the phone with a lead tech, if not we will send someone out to have to a look. It is our job to make sure that you have a fully functioning lift and will do what it takes to ensure that happens.
Metro Vancouver, Edmonton and surrounding areas,Winnipeg and surrounding areas , Metro Mississauga and Toronto.
With sufficient notice, we will reschedule the install without issue; however, if you cancel with less than 36 hours notice, you will be charged $1000 to cover the cost of our team's downtime.
You will be charged for the installation and then we will charge you a $500 revisit fee when we come and install the correct lift. It is important to ensure your site will fit the lift that you have chosen. please talk to your sales professional if you are at all unsure.
Our crew will not attempt the install if your concrete will not hold the lift. You will be charged for the install and then a $500 revisit fee for us to come back and install once you have the concrete fixed.
Our crew will wait and you will be charged $250/hour wait time fee.
We will need to know how much of a slope there is. Depending on the difference from post to post or side to side, you can purchase additional shims and anchors to make the lift level. We are usually able to work around a bit of a slope without issue.
We remind you during the ordering process to check and then double check all measurements prior to making the purchase. If there is any question in your mind, you can request a site survey if you are in our service area and one of our technicians will come to inspect the site. There is a $150. fee for this service.
Our crew arrives at our warehouse at 8am to load the lift. Once it is loaded, the installer will contact you to give you an ETA.
There may be KM charges, truck hours, accomodations, airfare and/or other associated expenses. To get the exact answer to this, please contact us for a detailed quote.
There are so many factors that contribute to selecting the correct lift for your needs. We can help you break down the options based on the space you have available, the vehicles that you own and what you are looking to achieve to find the right option for your needs.
We will happily come out and anchor it for you. There will of course be a service call fee for this visit.
On the babco website - find the lift you are interested in and it is under the manual/other tab.
Babco has been in business for over 30 years. We are your trusted source for all of your equipment needs, and we stand behind our products and services. We offer installation and servicing in many areas, and offer our own in house warranty on many products. We will always be here to support you before, during and after your purchase and we strive to establish lasting relationships with our customers.
We do the install checklist for 2 reasons- First is to protect you and to make sure that from the measurements that you have given us, we can confirm that your lift will fit. Second, it allows our technicians to be certain of the details on where they will be installing your new lift saving time, money and frustration. We want to make the install as quick and easy for you as possible and the more information that we have in advance, the more likely a seamless install becomes.
Bendpak has a 2 point safety system that includes a lock that needs air pressure to release them. Peak uses a manual lever to release their locks negating the need for an outside air source. Two different solutions for the same operation, your Sales Professional can go through which option is best for your specific situation.
Our techs are not certified electricians and are not qualified to do this part of the job. For the safety of all involved, a certified professional is the way to go.