Heavy-Duty Lift FAQ
Mobile Column Lift Frequently Asked Questions
The primary electrical components must be a minimum of NEMA 4 IP65 water splash resistant.
Yes, the forks are adjustable and you can lift a wide variety of trucks and equipment. Accessories such as light truck adapters, and chassis lifting beams are available to make the lifts more versatile. See your Heavy Duty lift expert for more info.
Each cylinder is equipped with an automatic burst (velocity) fuse check valve that automatically locks in the event of a catastrophic hydraulic hose or seal burst.
We can provide options for lifting all type of vehicles and equipment from forklifts to light trucks to anything you have in mind. The possibilities are endless and our sales professionals are here to help you find the perfect piece of equipment for you specific operation.
NO, the Columns will stay connected until instructed to do otherwise, The control will have a position memory and will not have to be reconfigured after each use.The columns will automatically re-establish communication between columns if the signal is dropped for any reason.
The column carriage shall run on premium PET (Polyethylene terephthalate) partially crystalline thermoplastic industrial glide bearings that have high sliding properties and dimensional stability. The glide bearings will have undergone cycle testing to not less than 20,000 cycles at full load to insure their long cycle life.
The achieved lifting height of the tire footprint at each lifting fork shall be no less than 70” as measured from the ground to the bottom of the tire
two (2) “Fiamm" brand 12 volt Industrial batteries model 12GL27. The battery life under normal operating conditions is estimated to be a minimum of ten (10) years. The batteries will be leak proof with sealed venting and made with thick impact resistant ABS plastic.
you can wirelessly pair the Omer mobile columns from 2-10 units giving a maximum lifting capacity of 190,000 lbs
Yes, Omer has extended warranty available for purchase - Please contact your HD sales rep for more information.
Provide floor conditions that meet the 4 1/2” thickness, 4000 psi strength and 2-degree level specified. Ensure that there is adequate drainage to continuously remove water away for the lift.
Although this is very uncommon, Wired communication cables are optional and available for purchase if you want to have the option of a wired connection as well.
The lifts will have a minimum anticipated “Cycle life” under normal use applications of not less than fifteen (15) years.
Manufacturer's Warranty: Lift system shall be warranted against defects in workmanship and material for a minimum period of two (2) years for ALL parts and 1-year labor. The batteries shall be warranted for a period of two (2) years with the second year “pro-rated”. The PET guide bearing shall have a lifetime parts warranty. The Hydraulic Cylinder seals shall be warranted for a minimum of ten (10) years covering replacement parts only. This warranty is limited will exclude misuse, abuse or lack of maintenance.
General Two-Post Lift FAQ
All cars and light trucks have approved lifting points that are specified by the vehicle manufacturer. It is critical that your vehicle is positioned properly relative to the centre line of the lift and centred between the columns. Cars that are front wheel drive and can be lifted asymmetrically. This allows the car to be positioned further back from the centre line of the lift. Often, a good rule of thumb is to start with the steering wheel lined up under the centre of the lift. When this is done, check the position of the four arms when they are extended to the recommended lifting points. The front lifting arm is manufactured on an angle and is considerably shorter than the rear arm, which will accommodate the asymmetric loading of your vehicle.
Yes . You just need to purchase the , std equalizer cables , Std length Safety cable, and the short version of the long hose.
No, you cannot install a two post lift on asphalt. Concrete must be a minimum of 4 -6" thick depending on capacity with a minimum rating of 3000 PSI.
Lifts can be installed but need to have the heating elements mapped so the bolts don't damage the heating system. We can help you find a suitable contractor to help in this regard.
Both BendPak and Peak offer a TURF Kit option for their 9-10K Capacity Lifts. The turf kit provides service on large fairway mowers to greens mowers, utility carts, sand groomers, fertilizer sprayers, golf and refreshment carts. Fully adjustable wheel span and fork assemblies fit a wide array of wheel arrangements.
1.Run the lift up and down a few times with no vehicle. 2.Lower arms to about 1 foot off the ground. 3.Slightly open the Allen bleeders on top of the cylinders, look for bubbles in the fluid. Once there are no more bubbles, close the Allen bleeders. This should take care of the issue.
1. Run the lift up and down a few times with no vehicle.
2. Lower arms to about 1 foot off the ground.
3. Slightly open the Allen bleeders on top of the cylinders, look for bubbles in the fluid. Once there are no more bubbles, close the Allen bleeders.
Yes you can, you would purchase an extension kit which would contain longer hydraulic hoses and cables.
We have different options to choose from depending on the weight capacity required, a sales rep would be happy to discuss options that suit your needs.
No. All 2 post lifts require anchoring. Talk to a sales representative about lift options that do not require anchoring.
We recommend frame cradle pads for added safety on all 2 post lifts
Frame cradle pads are recommended with 2 post lifts when working on any pickup truck or full frame vehicle. They act as a saddle for the frame rail and prevent the vehicle from sliding off the lift arms.
Symmetrical lifts have arms at the front and back that are the same length and design. Asymmetrical lifts have arms at the front and back that are different. This allows better access to the interior of the vehicle that is being worked on as well as better balance for different vehicles.
80-100 ft/lbs is sufficient and should be checked at regular service intervals.
Clear Floor models have the cables running over head giving a smooth floor under the lift making it easier to work under the car and roll tool boxes and transmission jacks under the car when working on it. Floor Plate models have the cables running under a cover on the floor giving more height for tall vans and the like. They both work well in different situations. Your sales professional can go over all of the details and find the perfect solution for your needs.
It's located inside the carriage about 18” down from the top of the carriage.
If you've got a heavy vehicle to lift, especially a truck, then you're going to want a set of cradle pads. Sturdy steel construction keeps the frame firmly between the cradle, while the treaded rubber mats protect the finish and reduce the chance of slippage.
General Four-Post Lift FAQ
Ramps are removable, We offer ramp stops as an add on accessory to flush the ramps with the runway or you can remove them completely.
Yes 220v is an option. The lift comes standard 110 but talk to a sales representative about changing to 220v
No, the vehicle cannot be stored on the car lift while the portable wheel kit is in use. This will damage the wheel kit and void any warranty for damage caused by this sort of incorrect usage.
You can leave the vehicle on the Jack indefinitely, as long as you leave the Rolling Jack engaged on its Safety Locks. Once the Safety Locks are engaged, the mechanical action of the lock holds the Vehicle up, so a loss of air or hydraulic pressure has no impact; your Vehicle is going to stay where you left it. Always leave your Rolling Jack either fully lowered or engaged on its Safety Locks.
6ft
You are welcome to leave your sub 9000 lb lift free standing but it is always recommended to put some sort of barrier between the posts and the concrete such as a yoga matt or recycled tire matting. 3mm rubber gym flooring also works great in this circumstance.
The 4 post lifts are stocked with steel and are available in an extended version as well. We also offer an aluminum option in standard or extended as well at extra cost.
Yes, any post on the lift can be shimmed
10 Gauge or 1/8th" steel with cold formed inner guide supports.
The Air-Operated Hydraulic Pump must be attached to an air supply: 20 cubic feet per minute (.57 cubic meters per minute) and 100 psi (7 bar).
90 seconds on 110V . 45 seconds on 220V power
No, a certified electrician is required to wire 220V power